How do you replace a CV joint on a 2005 Chevy Silverado?

12:57Suggested clip 118 secondsHow to replace CV Axle Chevy Silverado 00-06 – YouTubeYouTubeStart of suggested clipEnd of suggested clip

Can you drive a 4×4 without front axles?

Can you drive a 4WD truck without a front or rear drive shaft? Yes, this is possible if you drive a traditional 4WD with a lockable center differential. Remove the damaged drive shaft and lock the center differential. You will be able to safely drive the vehicle in front wheel drive or rear wheel drive mode.

How do you test a 4 wheel drive switch?

How do you test a 4 wheel drive switch?Locate the four-wheel drive high button on the dash.Drive the vehicle as normal and press the button or shift into 4Hi.Turn the vehicle to the left and right while moving.Locate the four-wheel drive low button on the dash or shifter.Stop the vehicle.Engage 4Lo by pressing the button or shifting.

How do I know if my 4wd switch is bad?

Also asked, how do I know if my 4×4 switch is bad? Difficulty engaging four-wheel drive A faulty switch may require the knob or button to be pressed or jostled several times before the four-wheel drive system comes on, and even then, it may have difficulty staying engaged.

Where is the 4 wheel drive actuator located?

A 4-wheel drive actuator is a device that allows you to automatically switch between two-wheel and four-wheel drive. This switch is installed on the front axle tube or on the differential housing.

How do I turn my 4 wheel drive off?

How do you manually disengage 4wd?Check to see if you have manual hubs and that they are in “free” mode.Put your vehicle into four-wheel high mode.Drive forward for about a quarter of a mile.Stop the vehicle and shift from four-wheel to two-wheel drive.Place the vehicle in reverse and drive backwards for 15 to 20 feet.

How much does it cost to fix 4wd?

On average, a remanufactured transfer case costs depending on the make and model of your vehicle. The cost of labor to install it is in addition to the price of the unit and will typically run between $400 and $800.

What does it mean when your truck says service 4 wheel drive?

The “Service 4WD System” message indicates a problem with the 4WD system that should be properly diagnosed and repaired. When the ignition key is turned from OFF-RUN-START and is released back to the RUN position after the vehicle starts, the 4WD warning light should go on for 1 to 2 seconds and then go out.

How do I know if my transfer case shift motor is bad?

Common signs include difficulty shiftinggears, grinding noises coming from underneath the vehicle,and jumping in and out of four-wheel drive. Click to see full answer. People also ask, what happens when transfer case goes bad? It may actually become difficult to shift gears anddrive the vehicle.

Can I still drive with service 4wd light on?

Usually labeled “Service 4WD”, when this light comes on, a code will be stored in the computer’s memory to help identify any issues. Depending on the problem, the four wheel drive may be disabled temporarily.

How do you know if an encoder motor is bad?

Since the encoder motor is located close to the ground, it is easily susceptible to damage due to road debris. One of the indications of a bad encoder motor is the flashing of the 4WD warning light in your vehicle’s instrument cluster. Replacing an encoder motor can easily be performed by a DIYer.

How do you test a motor encoder?

2:02Suggested clip 71 secondsTesting the Encoder Sensor – YouTubeYouTubeStart of suggested clipEnd of suggested clip

Why do encoders fail?

In such harsh environments, there are three common causes of encoder failure: 1) solid particulate or liquid contamination, 2) mechanical bearing overload, and 3) signal output failure. As a result of any of these problems, the encoder will cease to operate or the system will operate erratically.

What is the Tccm fuse?

It’s aregular 30 AMP fuse that powers the transfer case encodermotor and the shift control module. The Transfer Case Control Module (TCCM)is the brain behind the electronically shifted GM 4WDsystems.

What is a Tccm module?

The Transfer Case Control Module (TCCM) is a specialty of the General Motor’s 4WD operation. It controls the electronically-operated 4-wheel-drive system. All of its functions involve the shift – processing the shift request, executing it, and verifying the completion.

Where is the transfer case control module located?

Transfer Case Control Module: This is the system’s brain. It is located under the dashboard above the parking brake pedal, behind a large metal bracket.