Helpful tips

How do I reset my ReadyNAS admin password?

by Bobbi Devlin

How do I reset my ReadyNAS admin password?

You can reset your ReadyNAS Admin password by accessing http://ip_address_of_readynas/password_recovery. If you have forgotten the password recovery answer, you will need to perform a firmware re-installation to reset the admin password.

How do I change the password on my Netgear NAS?

Users can also change their passwords using the ReadyNAS change password tool.

  1. To change the password of your ReadyNAS user account:
  2. On a computer that uses the same LAN as your ReadyNAS system, visit https:///password_recovery/my_password.

What is the default password for Netgear ReadyNAS?

The default credentials to log in to the local admin page are: Username: admin. Password: password.

How do I reset my ReadyNAS without losing data?

How to Factory Reset Netgear ReadyNAS?

  1. First of all, turn the ReadyNAS device off and locate the Reset button on it.
  2. Take a hold of a paper clip or pin-like device.
  3. Press and release the ReadyNAS Reset button using the pin.
  4. Now, power up the device and again press the Reset button.
  5. Let the lights on your device turn on.

How do I access my ReadyNAS admin page?

Access the web admin page of the ReadyNAS by clicking Admin Page in RAIDar or enter the URL https://ReadyNAS_IP_address/admin – where ReadyNAS_IP_address is the IP Address seen in RAIDar.

How do I reset my QNAP password without losing data?

Use one of the following methods:

  1. Basic system reset using QES. Go to Control Panel > System > Hardware > Backup/Restore > Restore to Factory Default. Click Reset Settings.
  2. Basic system reset using the reset button. Power on the NAS. Press and hold the reset button for 3 seconds.

What is the default password for QNAP NAS?

admin
The default admin password is admin, you can login the NAS via admin/admin after resetting the NAS.

How do I reset my Netgear ReadyNAS?

How do I reset my Netgear ReadyNAS duo?

To perform a factory reset, continue to hold the Reset button until all Disk LEDs flash twice (once at 5 seconds and then 25 seconds later), and then release the button.

How do I Reset my NETGEAR ReadyNAS?

How do I Reset my NETGEAR password without security questions?

How do I recover my NETGEAR admin password using the password recovery feature?

  1. Launch a web browser from a computer connected to your router’s WiFi network.
  2. Enter routerlogin.net or routerlogin.com into your web browser’s address bar.
  3. Click CANCEL.
  4. Enter your router’s serial number.
  5. Click CONTINUE.

How do I reset the password for my ReadyNAS account?

Enter the email address and password recovery answer you enabled on your ReadyNAS storage system and click the Reset password and email button. NETGEAR resets your administrator password and sends an email message with the new password to you.

What happens when I reset the ReadyNAS back to factory default?

Resetting the ReadyNAS back to factory default will wipe out all configuration and data. Please understand this before continuing. Was this article helpful? Looking for more about your product?

How do I skip the volume check on a ReadyNAS?

Pressing and holding the POWER button for about 5 seconds (first blink of disk LEDs) on the v1 would result in skipping the volume check. NB: A ReadyNas is not an excuse not to have a backup. Fire, theft, multiple disk failures, other hardware failure, floods, user negligence etc. can all result in loss of data. 2016-05-06 06:19 AM

What is the default password for a Netgear NV+ device?

The default password varies depending on which unit you have and which firmware. If it is a NV+ running RAIDiator 4.x then it is ‘netgear1’ (no quotes) If it is a NV+ v2 running RAIDiator 5.3.x then it is ‘password’ (no quotes)